Pulley Ridge Hillshade Bathymetry TIFF image - UTM, Zone 17, NAD83

Metadata also available as - [Questions & Answers] - [Parseable text]

Metadata:


Identification_Information:
Citation:
Citation_Information:
Originator: VeeAnn A. Cross
Originator: Robert B. Halley
Publication_Date: 2005
Title:
Pulley Ridge Hillshade Bathymetry TIFF image - UTM, Zone 17, NAD83
Geospatial_Data_Presentation_Form: remote-sensing image
Online_Linkage:
<http://pubs.usgs.gov/of/2005/1089/data/bathymetry/hshade_img.zip>
Larger_Work_Citation:
Citation_Information:
Originator: VeeAnn A. Cross
Originator: David C. Twichell
Originator: Robert B. Halley
Originator: Kate T. Ciembronowicz
Originator: Bret D. Jarrett
Originator: Erika S. Hammar-Klose
Originator: Al C. Hine
Originator: Stan D. Locker
Originator: Dave F. Naar
Publication_Date: 2005
Title:
GIS Compilation of Data Collected from the Pulley Ridge Deep Coral Reef Region
Series_Information:
Series_Name: Open-File Report
Issue_Identification: 2005-1089
Publication_Information:
Publication_Place: Woods Hole Science Center, Woods Hole, MA
Publisher: U.S. Geological Survey, Coastal and Marine Geology Program
Online_Linkage: <http://pubs.usgs.gov/of/2005/1089>
Description:
Abstract:
Pulley Ridge is a series of drowned barrier islands that extends almost 200 km in 60-100 m water depths. This drowned ridge is located on the Florida Platform in the southeastern Gulf of Mexico about 250 km west of Cape Sable, Florida. This barrier island chain formed during the initial stage of the Holocene marine transgression. These islands were then submerged and left abandoned near the outer edge of the Florida Platform. The southern portion of Pulley Ridge hosts zooxanthellate scleractinian corals, green, red and brown macro algae, and a mix of deep and typically shallow-water tropical fishes. This reef community is in unusually deep water, and its extent and the controls on its distribution were unknown. To address these questions scientists from the U.S. Geological Survey Coastal and Marine Geology Program in cooperation with scientists from the University of South Florida Department of Marine Sciences have completed a detailed mapping of the southernmost 35 km of Pulley Ridge. The area was mapped using multibeam bathymetry, sidescan-sonar imagery, and high-resolution seismic-reflection profiling to define the geologic framework on which the reef is established. Submersible dives, remotely operated vehicle (ROV) transects, and transects of bottom photographs and video were collected to identify the corals and to map their distribution. This extensive suite of data has been compiled and preliminary analysis of the data suggests that the reefs are not tied to the ridge system, but instead are more broadly distributed. Whether reef distribution is controlled by oceanographic conditions or by subtle differences in the substrate that overlies the barrier island system is unclear, and are topics of continued research.
Purpose:
To provide high-resolution hillshade relief for the Pulley Ridge study area.
Time_Period_of_Content:
Time_Period_Information:
Multiple_Dates/Times:
Single_Date/Time:
Calendar_Date: 199904
Single_Date/Time:
Calendar_Date: 200005
Single_Date/Time:
Calendar_Date: 200109
Single_Date/Time:
Calendar_Date: 200304
Currentness_Reference: ground condition
Status:
Progress: Complete
Maintenance_and_Update_Frequency: None planned
Spatial_Domain:
Bounding_Coordinates:
West_Bounding_Coordinate: -83.791165
East_Bounding_Coordinate: -83.591875
North_Bounding_Coordinate: 24.998196
South_Bounding_Coordinate: 24.672987
Keywords:
Theme:
Theme_Keyword_Thesaurus: General
Theme_Keyword: bathymetry
Theme_Keyword: CMGP
Theme_Keyword: Coastal and Marine Geology Program
Theme_Keyword: coral
Theme_Keyword: coral reef
Theme_Keyword: TIFF
Theme_Keyword: OF 2005-1089
Theme_Keyword: Open-File Report
Theme_Keyword: reef
Theme_Keyword: U.S. Geological Survey
Theme_Keyword: USGS
Theme_Keyword: Woods Hole Science Center
Theme_Keyword: hillshade
Theme_Keyword: field activity serial number 01010
Theme_Keyword: field activity identifier S-1-01-GM
Theme_Keyword: field activity serial number 03002
Theme_Keyword: field activity identifier S-1-03-FL
Place:
Place_Keyword_Thesaurus: General
Place_Keyword: Florida
Place_Keyword: Florida Shelf
Place_Keyword: Gulf of Mexico
Place_Keyword: North America
Place_Keyword: Pulley Ridge
Place_Keyword: United States
Access_Constraints: None.
Use_Constraints:
The U.S. Geological Survey must be referenced as the originator of the dataset in any future products or research derived from these data. This information is not intended for navigational purposes.
Native_Data_Set_Environment:
Microsoft Windows XP Version 5.1 (Build 2600) Service Pack 2; ESRI ArcCatalog 9.0.0.535
Cross_Reference:
Citation_Information:
Originator: R. He
Originator: R.H. Weisbert
Publication_Date: 2002
Title: Tides on the West Florida Shelf
Series_Information:
Series_Name: Journal Physical Oceanography
Issue_Identification: v.32, p. 3455-3473

Data_Quality_Information:
Lineage:
Source_Information:
Source_Contribution:
Multibeam bathymetry was collected with a Kongsberg Simrad EM3000 system. This dataset represents 4 years of data collection. 1999 data collected April 26-27 aboard the Florida Institute of Oceanography (FIO) R/V Bellows. 2000 data collected May 9-10 aboard FIO's R/V Suncoaster. 2001 data collected September 5-10 aboard FIO's R/V Suncoaster. 2002 data collected April 24-29 aboard FIO's R/V Suncoaster.
Process_Step:
Process_Description:
All raw data files were processed with CARIS HIPS (Hydrographic Information Processing System) version 5.3 with the following workflow: a) created vessel configuration file (VCF) for each cruise. Initial roll, yaw, pitch, and x,y,z axis parameters were set to zero. This information was incorporated into the data at the time of collection as the installation parameters. b) created a new project directory for the HIPS data. This data set was broken down by year. The 2000 data was added to the 1999 data and made into one project, but the other years each have their own projects and field sheets. c) raw line files from em3000 software were brought into CARIS conversion wizard. The conversion wizard converts raw data files to HIPS format and saves the files to a project directory. d) each line was evaluated with the navigation editor to clean the vessel's navigation data. Two know jumps in speed were searched for and the position fixes along with the fixes before and after were rejected with interpolation. The lines were also evaluated with attitude editor to view and clean the motion sensor data like heave and roll. e) a tide file was created for each cruise using a model created by Ruoying He in the Ocean Circulation Group at the Univ. of South Florida (see cross reference section for reference). f) All lines were then merged to create position/depth data for each sounding. g) filters were created for each survey and set to: min depth 40 m, max depth 115 m (as requested by researchers), nadir depth 3.2, angle form nadir 65 degrees port and starboard. Filters applied after merging. h) after merging a weighted mean seabed surface (grid) was created at a 5 m resolution. i) ran the statistical surface cleaning. Cleaning by 2 standard deviation 95%, polynomial 1: tilted plane, tile bugger 10%. j) created subset tiles of 500 square meters. Each tile was opened in subset editor to examine and clean soundings in both 2D and 3D. Tiles viewed in subset editor reveal when calibration is necessary or if there is a sound velocity error. k) if needed, a subset was examined with the calibration function to measure parameters like transducer mounting offsets (pitch, roll, heading). The calibration surveys were performed and allowed adjustments of the survey data parameters and modifications were written to the VCF. Survey modifications were as follows: 2000 survey - VCF for both days adjusted to yaw -9.0 and roll 0.35. 2001 survey - VCF for day 249 (9/6/01) adjusted roll to -0.25, for the day 251 adjusted roll to -0.35. 2003 survey: VCF for days 114, 115, and 119 adjusted to delta z +3.5m, for days 114 and 115 roll adjustment to -0.40. l) after adjusting the VCF files all associated lines for each survey were remerged and then regridded. m) grids were exported to x,y,z using the weighted grid to ASCII option selected units of geographic decimal degrees (DD). Five files were exported: PR_00_99_5m.xyz, PR_01_5m.xyz, PR_03_5m.xyz, PR_sw_03_5m.xyz, and PR_gapfill_5m.xyz.
Process_Date: 2004
Source_Produced_Citation_Abbreviation:
PR_00_99_5m.xyz, PR_01_5m.xyz, PR_03_5m.xyz, PR_sw_03_5m.xyz, and PR_gapfill_5m.xyz
Process_Contact:
Contact_Information:
Contact_Person_Primary:
Contact_Person: Kate T. Ciembronowicz
Contact_Organization: U.S. Geological Survey
Contact_Position: Research Assistant
Contact_Address:
Address_Type: mailing and physical address
Address: 600 4th Street South
City: St. Petersburg
State_or_Province: FL
Postal_Code: 33701-4846
Contact_Voice_Telephone: (727) 803-8747 x3124
Contact_Facsimile_Telephone: (727) 803-2031
Contact_Electronic_Mail_Address: kciembro@usgs.gov
Process_Step:
Process_Description:
Each of the x,y,z files were run trough Proj4.1 to convert the geographic coordinates to UTM, Zone 17, NAD83.
Process_Contact:
Contact_Information:
Contact_Person_Primary:
Contact_Person: VeeAnn A. Cross
Contact_Organization: U.S. Geological Survey
Contact_Position: Marine Geologist
Contact_Address:
Address_Type: mailing and physical address
Address: 384 Woods Hole Rd.
City: Woods Hole
State_or_Province: MA
Postal_Code: 02543-1598
Contact_Voice_Telephone: (508) 548-8700 x2251
Contact_Facsimile_Telephone: (508) 457-2310
Contact_Electronic_Mail_Address: vatnipp@usgs.gov
Process_Step:
Process_Description:
All the individual Pulley Ridge reprojected bathymetry files were combined into a single x,y,z file called allpr.xyz.
Source_Produced_Citation_Abbreviation: allpr.xyz
Process_Contact:
Contact_Information:
Contact_Person_Primary:
Contact_Person: VeeAnn A. Cross
Contact_Organization: U.S. Geological Survey
Contact_Position: Marine Geologist
Contact_Address:
Address_Type: mailing and physical address
Address: 384 Woods Hole Rd.
City: Woods Hole
State_or_Province: MA
Postal_Code: 02543-1598
Contact_Voice_Telephone: (508) 548-8700 x2251
Contact_Facsimile_Telephone: (508) 457-2310
Contact_Electronic_Mail_Address: vatnipp@usgs.gov
Process_Step:
Process_Description:
This xyz file was brought into Surfer to create a 5x5 m grid with the bounds xmin: 218042.5, xmax: 237717.5, ymin: 231553.5, ymax: 2767328.5. The gridding parameters were block kriging, linear, slope = 1, aniso = 1,0, radius1=30, radius2=30. Output was sent to allpr_blockkrig.grd.
Source_Used_Citation_Abbreviation: allpr.xyz
Source_Produced_Citation_Abbreviation: allpr_blockkrig.grd
Process_Contact:
Contact_Information:
Contact_Person_Primary:
Contact_Person: VeeAnn A. Cross
Contact_Organization: U.S. Geological Survey
Contact_Position: Marine Geologist
Contact_Address:
Address_Type: mailing and physical address
Address: 384 Woods Hole Rd.
City: Woods Hole
State_or_Province: MA
Postal_Code: 02543-1598
Contact_Voice_Telephone: (508) 548-8700 x2251
Contact_Facsimile_Telephone: (508) 457-2310
Contact_Electronic_Mail_Address: vatnipp@usgs.gov
Process_Step:
Process_Description:
This grid was then filtered with an 11x11 IDW filter. Blank nodes were ignored. The output grid was allpr_blockkrig_idwfil11x11.grd.
Source_Used_Citation_Abbreviation: allpr_blockkrig.grd
Source_Produced_Citation_Abbreviation: allpr_blockkrig_idwfil11x11.grd
Process_Step:
Process_Description:
This grid was then exported to a surfer ASCII grid format filename out_allprfil_asc.grd.
Source_Used_Citation_Abbreviation: allpr_blockkrig_idwfil11x11.grd
Source_Produced_Citation_Abbreviation: out_allprfil_asc.grd
Process_Step:
Process_Description:
This surfer ASCII grid was converted to an ArcView ASCII grid using the ArcView 3.3 extension : Surfer extension 2.8 downloaded from the ESRI website. The output filename was out_allprfil_asc.asc.
Source_Used_Citation_Abbreviation: out_allprfil_asc.grd
Source_Produced_Citation_Abbreviation: out_allprfil_asc.asc
Process_Step:
Process_Description:
This ArcView ASCII grid was then imported to ArcView 3.3 and converted to and ESRI binary grid called allpr_fil.
Source_Used_Citation_Abbreviation: out_allprfil_asc.asc
Source_Produced_Citation_Abbreviation: allpr_fil
Process_Step:
Process_Description:
This grid was then cropped to a polygon which removed extraneous lines outside the majority of the data collection area. The resulting grid is allpr_filcrop.
Source_Used_Citation_Abbreviation: allpr_fil
Source_Produced_Citation_Abbreviation: allpr_filcrop
Process_Step:
Process_Description:
A hillshade grid was created using ArcGIS 9.0, default parameters.
Source_Used_Citation_Abbreviation: allpr_filcrop
Source_Produced_Citation_Abbreviation: hshade
Process_Step:
Process_Description:
Within ArcView 3.3, the extension 'Image Conversion - Georeferencing 2' was used to convert the hillshade grid to a georeferenced TIFF image.
Process_Step:
Process_Description:
Corel PhotoPaint version 11 was used to convert the 24-bit image to an 8-bit grayscale image.

Spatial_Data_Organization_Information:
Direct_Spatial_Reference_Method: Raster
Raster_Object_Information:
Raster_Object_Type: Pixel
Row_Count: 7133
Column_Count: 3891
Vertical_Count: 1

Spatial_Reference_Information:
Horizontal_Coordinate_System_Definition:
Planar:
Grid_Coordinate_System:
Grid_Coordinate_System_Name: Universal Transverse Mercator
Universal_Transverse_Mercator:
UTM_Zone_Number: 17
Transverse_Mercator:
Scale_Factor_at_Central_Meridian: 0.999600
Longitude_of_Central_Meridian: -81.000000
Latitude_of_Projection_Origin: 0.000000
False_Easting: 500000.000000
False_Northing: 0.000000
Planar_Coordinate_Information:
Planar_Coordinate_Encoding_Method: row and column
Coordinate_Representation:
Abscissa_Resolution: 5.000000
Ordinate_Resolution: 5.000000
Planar_Distance_Units: meters
Geodetic_Model:
Horizontal_Datum_Name: North American Datum of 1983
Ellipsoid_Name: Geodetic Reference System 80
Semi-major_Axis: 6378137.000000
Denominator_of_Flattening_Ratio: 298.257222

Entity_and_Attribute_Information:
Detailed_Description:
Entity_Type:
Entity_Type_Label: hshade
Attribute:
Attribute_Label: ObjectID
Attribute_Definition: Internal feature number.
Attribute_Definition_Source: ESRI
Attribute_Domain_Values:
Unrepresentable_Domain:
Sequential unique whole numbers that are automatically generated.
Attribute:
Attribute_Label: Value
Attribute:
Attribute_Label: Count

Distribution_Information:
Resource_Description: Downloadable Data
Standard_Order_Process:
Digital_Form:
Digital_Transfer_Information:
Transfer_Size: 26.488

Metadata_Reference_Information:
Metadata_Date: 20050513
Metadata_Contact:
Contact_Information:
Contact_Person_Primary:
Contact_Person: VeeAnn A. Cross
Contact_Organization: U.S. Geological Survey
Contact_Position: Marine Geologist
Contact_Address:
Address_Type: mailing and physical address
Address: 384 Woods Hole Rd.
City: Woods Hole
State_or_Province: MA
Postal_Code: 02543-1598
Contact_Voice_Telephone: (508) 548-8700x2251
Contact_Facsimile_Telephone: (508) 457-2310
Contact_Electronic_Mail_Address: vatnipp@usgs.gov
Metadata_Standard_Name: FGDC Content Standards for Digital Geospatial Metadata
Metadata_Standard_Version: FGDC-STD-001-1998
Metadata_Time_Convention: local time
Metadata_Extensions:
Online_Linkage: <http://www.esri.com/metadata/esriprof80.html>
Profile_Name: ESRI Metadata Profile

Generated by mp version 2.8.6 on Fri May 13 13:30:35 2005